Car Detailing

 
 


 

Car Detailing

 

Exterior:

 

 
You’ll need
 

  • Three 20ltr buckets, two white and one black! (Wheels, Wash, Rinse)
  • Two Scratch Guards (One for the Wash and one for the Rinse Bucket)
  • Lambswool Wash mit or Glove
  • Refract Domestic Foam Gun (Standard Hose Adaptor)
  • Refract Snow Foam (30ml)
  • Two Refract Microfibre Towels of your choice,
  • One Silicon Water Squeegie
  • One Large Plush Microfibre Drying Towel or Waffle Drying Towel
  • One Refract Window Towel
  • One set of Refract Detailing Brushes
  • One set of Refract Lambswool Wheel Woolies
  • Refract Iron Degreaser
  • Refract Tyre Enhancer
  • Refract Tyre Applicator

 

Step One.

 
Setup and plug in your Water Hoses, Pressure Washer, Compressor and air lines Neatly and logically.
 
Take your Three Clean Buckets and Fill with Water (30 degrees is perfect temp) to the top. Its tempting to wash with hot water but a lot of the times we find that the water spotting just happens quicker.
 
Place Your Blue Grit Guard In one of the White Buckets and The Red One in the other. Place Lids or cover both buckets to avoid any dust from getting in them.
 
Place 30-40Mls of Degreaser and Wheel Cleaner into the Black Bucket and give it a good mix.
 

Step Two.

 
Take your Wheel Woolies and place them in the bucket along with a dedicated Detailing brush. Take your Refract Iron Remover and spray liberally in and around the wheel and Brake Caliper areas. You will see before your very eyes that the liquid will turn a purple colour and that hard baked on Grease and Brake Dust will be lifting safely off the surface!
 
Take your appropriate sized Wheel Woolie and Start to agitate the inside the wheel to work the product around. Use the smaller Woolies to Get in around all the wheel spokes and various nook and crannies of the brake caliper and rotor hub.
 
Use your detailing brush to get between the spokes and give everything a good clean! (Always start from the Bottom and work your way up and around the wheel constantly rinsing your tools) Work quickly but carefully, painted gloss wheels are easy to scratch if you’re too rough on them. Rinse the wheel after the Iron remover has done its thing and re-apply if the wheel is excessively dirty! This is the major cause for your gloss wheels looking scratched. Always work clean! Don’t be dragging excessively dirty water across any surface if you can help it!. One good tip is to follow with a small stream of water on your tool whilst rinsing the wheel at the same time.
 
Scrub the tyre with a stiff brush and use your dedicated wheel brush to clean in amongst the tread and also agitate the wheel arches if you can get into them.
 
Rinse clean with Domestic Water pressure or its best to use your high pressure cleaner to blast away the remaining dirt and grime!
 
Your brake rotors (Unless you’re sporting Carbon ceramic) will almost instantly start to form surface rust! To combat this you must dry the rotor straight away with a towel or its best to use compressed air!
 
You wont completely stop it happening! Don’t stress! As soon as you go for a drive the disc will be cleared when you depress the brake pedal.
 
You will be getting the rotors wet again for the next washing step so either cover the wheels in a plastic garbage bag or just leave them for the after detail show off cruise to clear the rust! (You know what I mean!).
 
Clean up and rinse your Wheel detailing tools and stow them away for next time!

Step Three

Take you Foam Gun (Whatever type you’re using and fill it up with water then add 30-40mls of Refract Snow Foam Liquid and Screw the bottle to the Sprayer housing.
 
Connect the Foam gun to your hose or Pressure washer and Cover the entire vehicle whilst adjusting the amount of Liquid to Water ratio and Spray Pattern Width!
 
Let the Foam do its job and soak in for up to 10 Minutes Max! DO NO LET THE FOAM DRY ON THE PAINT, it’ll create water Streaks!
 
Rinse the Foam off the car starting at the roof and working the Foam/Dirt/Debris down and away, work slowly and make sure all the foam has been rinsed before proceeding down any further!
 

Step Four

 
Take the lids off your White Buckets and Add 30-40mls of Ph Neutral Wash Shampoo. Give it a blast with your hose to mix the product thoroughly!
 
Place your Wash Mit/Glove into the first bucket with the Blue Grit Guard and procedd to wash the ‘Top’ of your car!. Start by working half of the car at a time!
 
Place your hand in the Wash mitt and let the shampoo drain out of the mitt and onto the first haf of the roof!. Proceed to wash the Roof Panel with minimal pressure short strokes maybe once or twice only! (Not Circle Swirling!).
 
Plunge your now contaminates wash mitt into the other ‘Rinse’ Bucket and quickly twist your wrist to allow any debris in the mitt to fall out and drop to the bottom of the bucket to get trapped under the Grit Guard!. Plunge the clean Mitt back in to the ‘Wash’ Bucket and proceed to do the rest of the ‘Top Half’ of the car. This means all the panels above the half way crease or trim that most cars have!. This is the ‘Cleaner’ sections of the car generally!. The lower sections of the doors, rear bumper, front lower bumper and lower quarter panels will be much dirtier. Once you completed the entire ‘Top Half’ of the car. Tip both your Wash and rinse Buckets out and quickly refill!. At this stage you may want to pressure wash the suds and debris away to avoid the shampoo drying out too quickly!
 
Immediately after this Step everyone wants to take a break, grab a drink, pat the dog etc. DON’T!, You must get that car dry!
 
Take you weapon of choice (Silicon Squeegie, Microfibre Waffle Towel, Big Blue Drying Towel, Air Compressor Blow Gun or a combination of all) and dry the car thoroughly!
 
We recommend you start with the Windows and Glass. Use your squeegee followed by Waffle Towel.
 
Move onto the Plastics, Be careful here as the the Waffle towel may become blackened from the previous products on the rubbers! Compressor Blow Gun is your friend here! Blow the water off then lightly run a Microfibre Towel or Waffle Towel over the remaining.
 
Next is the Paint
 
If you’re lucky enough to have Refracts VMAFA Ceramic coating already on your car then all you need here is your Blow Gun and Big Blue Drying Towel. The water will basically fall off the cars paint and trims.
 
If the paint doesn’t have a ceramic coating or hasn’t been waxed recently you will just have to us a combination of the Squeegie, Waffle Towel and Drying Towel and work quickly to Dry it all off!
 
Whilst this may some counter productive, you can mist Refracts Quick detailer spray in front of the Microfibre Towel to assist in Drying whilst applying a nice shiny protectant. (This will only be beneficial if you’re not proceeding to the polishing stage!). If you are proceeding to polishing you can mist some demineralised water as you dry so the Big Microfibre Towel doesn’t ‘Grab’ or ‘Drag’
 
The technique
 
Step Three.
 

Interior:

 
You’ll Need
 

  • Vacuum cleaner (Wet or Dry or Combination) with attachments to reach tight areas. Pet Hair Attachments are a great tool too!)
  • A Pumice Stone. (Hard soap bar sized Stone to brush and collect pet hair). You can get these from your local Supermarket or Hardware store in the Cleaning Sections.
  • Refract Microfibre Towels for Applying Products, Dusting Components and for taping around the end of the Vacuum to aid in lifting dust and avoiding scratching the delicate interior surfaces!
  • Refract General Purpose Cleaning Liquid
  • Refract Interior Plastic, Vinyl and Dashboard Protectant
  • Refract Window Cleaner and Towel
  • Refract Detailing Brushes. (Use these to ‘Chase’ the Dust with the Vacuum Cleaner). Great for lifting Dirt and Dust from Sensitive surfaces!
  • Expert Detail (Pressure Washer and Air Compressor Required)

 

Exterior:

 
You’ll Need:
 

  • Basic Wash Products plus
  • Refract Detailing Clay Bar (Fine, Medium or Coarse dependant on level of contamination. (More on this later!) and or
  • Clay Product of Choice, (Clay Cloth, Clay Hand Pad, Clay Dual Action Pad,)
  • Refract Clay Bar Product Lubrication
  • Refract Snow Foam Gun – High Pressure
  • VMAFA High Pressure Tornado Cleaning Gun – High Pressure

 

Interior:

 
Basic Detailing Products plus:
 
VMAFA Tornado Cleaning Gun (Air Compressor Required with large tank capacity). Simply Add 1:20 into the Cleaning Pot, fill with Demineralised or Filtered Water (To avoid any un-necessary water spotting) and clean the dirt, dust and debris away with ease! Follow up with Refract Interior Protectant and Quick Detailer on a soft Application pad or Towel and you’re done!
 
Air Blow Gun Attachment (Local Hardware Stores).
 
Use this to completely blow out the dust and debris from carpets, window recesses, dash board vents and intricate spots prior to you vacuuming.(Or couple it together) Start from Passenger side and Open the doors on the drivers side, Blow the dust and debris right out the door! Try and get an atachment that is compact with a Rubber or Plastic tip to avoid scratching or chipping sensitive surfaces!
 
Carpet Cleaning Machine. (Steam or Wet)
 
These cleaning machines are cheap enough to buy and can do a fantastic job of Cleaning and restoring your Carpets and Seats.
 
Spray Refracts Carpet and Seat cleaner into the surface and let soak in, agitate the stain with your Interior Cleaning Brush and then use your Steam or Wet Cleaning Machine to extract the stain. Follow up with an Odour Remover and Fabric Freshener.
 
Basic Polish and Wax – Dual Action Polisher
 
Recommend you have expert Level Wash Products and conduct this procedure after a thorough wash undercover, in the shade or somewhere sheltered with no chance of the sun or the elements from ruining your work!.
 
Always have plenty of room to move around the vehicle so you can open the doors, move buckets around, position your pressure washer and set up base camp for your detailing trolley or table.
 
You will be running power cables to your Polishing Machine, Hose Line for the Pneumatic Guns, Water Hose lines from the wash and not to mention the Water Line from the pressure washer in the mix just to make
 
it interesting!. Consider using Waterproof Junction Boxes and Plug protectors from your local hardware store to increase safety aspects of water, electricity and high pressure air lines.
 
Select your desired location for the detailing to take place. Clear away all loose debris, junk and anything that you don’t want to get wet or get snagged on the many cables and hose that your about to use.
 
Pressure wash the floors area so it’s clear of excessive debris and Dirtt!. Sand is your enemy! One tiny grit of sand in you polishing pad, microfiber towel or blown on the paints surface from surrounding dirty areas will have devastating affects. WORK AND STAY CLEAN!, Hose away the dust and spider webs from around the area so that you minimise the chance of dust and debris falling on you paint prior to Polishing which will find its way into the DA Pads! (Refract recommend at least two to three polishing pads per car for maintenance detailing). We will talk more about this in cleaning tips and tricks!
 
Get yourself a decent fan to keep a constant flow of air blowing across the car! Any dust that falls will be quickly blown away!
 
A good tip is to wet down the surrounding walls if you can! If you have Gyprock walls then use a general purpose duster to remove as much dust as possible and even run the vacuum around the corners. (More on Interior and Vaccuming Later on)
 
If you have an extraction fan then definitely use it!
 
Temperature is important as polish can ‘Dry Out’ very Quick in temps above 30 Degrees. Have a Portable Fan Running or Begin early in the morning before the heat sets in. (The sun is your worst enemy!) The car will water spot almost instantly if left in the sun with water on it!
 

  • Refract 15mm Dual Action Polisher
  • Refract Microfibre Cutting Pad
  • Refract Microfibre Finishing Pad
  • Refract Cutting Compound
  • Refract Finishing Wax Liquid
  • Or Refract Palm applied Vehicle Specific Wax
  • Air compressor with blow gun

 
Snow foam bottle attachment for pressure washer (ill send you one when i get my stock in, please advise brand of sprayer, gerni, karcher etc) dont buy online, youll get ripped off!. (This foams the car and soaks it prior to washing) Snow foam liquid, online, carecareproducts.com.au. $20
 
Fluffy lambswool wash mit $55
 
Detailing paint brushes (bunnings have really soft ones but they’re like $13 bucks each) will prob send u some too!
 
To get yourself started tho, just get the basics and ill hook you up soon with some good gear later!
 

Step One.

 
Car in shade, cool, after sunset, before sunrise.
 
Fill the black bucket with diluted degreaser and a bit of shampoo and wash the wheels with a brush and cloth, rinse off
 

Step Two.

 
Pressure wash the whole car removing all the dirt and dust, start from the top down
 

Step Three.

 
Fill a white bucket with COLD water and add some suds, place cooling racks in the bottom, fill the second bucket with cold plain water
 

Step Four.

 
Using microfibre cloth, soak it in the suds and twist the water and suds over the car to soak
 
Proceed to wash the paint lightly in parallel to body panels movements, no round and round. Start from the roof down.
 
Rinse the cloth every body panel in the plain water bucket and work around the car, replacing water in buckets maybe three times for a car you size.
 

Step Five.

 
Rinse with pressure washer and dry with either compressor and/or waffle/microfibre towel. (NO CHAMOIS! Have a sacrificial burning ceremony of those things!)
 

Step Six.

 
Mist detailer spray on the paint and follow directions on bottle with a low pile microfibre cloth, not one that u washed with! (A new/clean dry one !)
 

Step Seven.

 
Dress your tyres with gel
 

Step Eight.

 
Use protectant spray on all black trims, plastics, headlights, roof racks, everything beside the paint (very important to do this every time u wash)
 
Use this on interior plastics/dash as well!
 
Spray in cloth tho not surface
 
Don’t ever use armourall etc on ur plastics, it’ll dry out eventually.
 
The internal windscreen only gets dirty because the heat from shit products gasses off and sticks to the glass!
 

Step Nine.

 
Go for a drive in your shiny ride!
 
This is a very basic wash! They’re are many other things u can do to make the paint look a lot better but wait until my website is up and it’ll all be in my blogs.

 

[related_posts_by_tax format="thumbnails" show_date="true" image_size="medium" link_caption="true"]

Leave a Reply

Your email address will not be published. Required fields are marked *